Poly F405 2S-4S 20A AIO V1.2

Hardware Specs

• FC MCU: STM32F405RGT6( Cortex®-M4 168Mhz )
• Built-in OSD: AT7456E
• Built-in IMU: BMI270
• Built-in 8M Flash Blackbox
• Built-in Current Meter
• ESC MCU: EFM8BB21 ( 8bit 50MHz )
• UART: UART1 ( for VTX by default ), UART2, UART3, UART4 ( supports SBUS ), UART5 
• Other interfaces: IIC ( IIC2 ) , LED_Strip, Buzzer
• The through holes for power lead: big enough to fit 16AWG wire
• 8 Motor Outputs ( The onboard esc have been used for 4 motor outputs. You can add 4 external esc if you want to use the other 4 motor outputs )

Electronics Specs

• Input Voltage: 6.50-20.0V( 2S-4S LIPO/LIHV )
• Power Output: 5V 2A
• Continuous Current: 20A

Firmware

• FC Betaflight Target: TUNERCF405
• ESC Firmware: Bluejay P-H-25

Motor Size Supported

• 1102~1104, 1202~1204, 1303, 1404

Recommended Capacitor 

• A 35V 220uf capacitor is included. A 35v 220-470 uf capacitor with low ESR is recommended if you want to swap the default one.

Dimensions

• Size: 33mm x 33mm
• Mounting Holes Pattern: 25.5 x 25.5mm   Room for M3.5 grommets to make M2 mount
• Weight: 6.1g

Note about the FC Firmware Preflashed to the Poly F405 V1.2

The default betaflight firmware version on the Poly V1.2 is 4.5.1, because the version limits and the product testing needs, the default settings are CRSF protocol and analog OSD mode. For HD digital and other receiver users, please reflash the firmware to include HD OSD options and other receiver protocols.

------updated on 2024/8/27

Note about the ESC firmware Preflashed to the Poly F405 V1.2

The default Bluejay firmware on the Poly F405 V1.2 is 0.21. The start up power is lower than the previous version V0.16. If you find your motor doesn't spin up, please try to increase the start up power.

Check out the article below to see how to set up the startup power and motor idle.
https://github.com/bird-sanctuary/bluejay/wiki/Setup

------updated on 2024/8/27

Note for Motor Choice

1404 is the maximum motor size that the Poly F405 V1.2 supports. About the KV value, please avoid using high kv 1404/1303 motors, such as 1404 6000KV.  For the 1404 size motor, 3800kv is recommended.

Note for Capacitor Installation

Please solder the capacitor directly to the onboard capacitor soldering pad. We highly recommend that you do this when you build a 4S quad.

Note for Receiver and VTX Setup

Please power up the receiver and VTX by the battery during the binding and setup process. Because the 5V from USB does not power the receiver and VTX.

Note for Buzzer Choice

Only the buzzer with a built-in drive circuit can be used on this AIO flight controller. A common micro buzzer (that only has two legs and without PCB board) is incompatible with the Poly F405 2S-4S AIO. We have released the buzzer with a built-in driver circuit. Buy it here.

Download the wiring diagram here.

• 1 * Poly F405 2S-4S 20A AIO V1.2
• 1 * XT30 pigtail with 18awg wire
• 1 * 35V 220uf capacitor 
• 6 * grommets

Shipped from Warehouse in Shenzhen, China
All orders placed on our website will be packaged and shipped from our warehouse in Shenzhen, China.

Shipping Methods & Duty Fee
We offer standard registered mail shipping to all countries and DHL express shipping to certain countries. FYI: if you can’t see the DHL option on the checkout page, that means we don’t provide DHL shipping service to your country at the moment. You don’t need to be worried about paying the duty fee if you are located in the European Union countries, because we have already paid the VAT in advance.

Detailed ETA
DHL: 5-7 days
Registered Air Shipping: 7-12 days for countries like the US, European countries, Japan, Korea and other southeast Asian countries. For detailed ETA, please check out our support article here.
Either you choose DHL or registered air shipping, you'll get a tracking number and a tracking link via email after we ship out your orders. So you can keep track of the parcel all the time.